问题现象:

① 通电后焊接头尾部电机出现啸叫 / 摆动红光异常 / 发热 / 无法调整摆动宽度

②直接烧坏镜片, 出现密封圈和聚焦镜片同时烧坏的情况

Problema Phaenomenon:

① Post electrifying, in motricium ad cauda de Welding caput apparet ululatus / abnormes rubrum lux adductius / febrem / non potuit ad adjust adductius latitudine.

② recta uri de lens et signantes circulum et focusing lens uri simul.

问题原因与解决方案:

控制盒内的驱动器控制电机摆动, 通过电机线链接, 当出现信号错误 (电机线接触不良, 断路), 外部干扰, 或者驱动器与电机不匹配的情况下, 可能出现 ① ①.

Causas problems et solutions:

Et coegi in potestate arca controls motricium ad adductius. Per motricium filum link, cum sit signum errorem (pauper contactus motricium filum, aperire circuitu), external et motricium, aut mismatch inter coegi et motricium, quaestio ① potest.

如出现②的问题, 建议检查周边的干扰源, 如未出现干扰源, 则可能是电机线故障, 直接更换电机线即可

Si est quaestio in ②, id est suggesserant ad reprehendo in circuitu intercessiones fontibus. Si nullum intercessiones fontem, ut sit motricium linea culpa, ita reponere motricium linea recta.

① 驱动器与电机的连接线端子接触不良 (Sup20s 款)

在 SUP20s 的焊接枪, 采用了连接端子内置的方式, 接触不良可能导致信号的异常从而引起啸叫, 尝试重新拔插

① Et connectens filum terminatio inter coegi et motricium in pauperes contactus (SUP20s).

In Welding gun in SUP20s adoptat aedificatum, in nexu terminatio. Pauper contactus potest ad abnormes signum, quod potest causare ululatus. Try ut rursus plug est.

②驱动器与电机的连接线五芯航插有断路 (sup15s 款)

在 sup15s 的焊接枪上, 电机信号和电源通过航插接口连接 (两根黑色的线), 应拆开航插接口, 检车各焊接引脚是否有断裂或虚焊

② Est aperta circuitu in quinque-core aeria et plug ex connectens linea inter coegi et motricium (sup15s).

De Welding gun supplementum, motricium signum et potentia copia connectantur per aeria obturaculum-in interface (nigrum fila). Aerial obturaculum, in interface debet disassembled reprehendo utrum welding paxillos currus fracta aut virtuals volutpat.

③前提: 如果摆动是正常的, 没有出现红光闪烁的情况, 且接线确认没问题, 那说明是驱动器与电机不匹配或干扰

这种出现在新装设备或更换枪头的设备上, 可以通过调整驱动的电位器来改善.

电位器位置: y 轴 (下图左侧) 插头上方从左到右, 第七个的位置

③ praemissa, si adductius est normalis, ibi est rubrum lux coruscans, et wiring est confirmatus esse ok, id est quod coegi et motricium non aequare vel intermixti.

Huiusmodi specie in nuper installed apparatu vel apparatu cum gun capitis replaced potest melior a adjusting pulsus potentiometer.

Potentiometer positio a sinistra ad ius super plug in y axis (sinistra figura infra), septima positio.

调整方法: 通电状态下用一字螺丝刀朝一个方向拧, 如果超过 X 圈无反应, 在拧回来复位, 然后继续朝另外一个方向拧.

(如果调整第七个电位器无反应, 那么久调整从左到右第四个)

Temperatio modum: Turn in unam partem screwdriver cum sit amet. Si nulla responsione post X vicissim convertat eam reset et continue convertat in altera.

(Si septimus potentiometer non respondit, adjust quarta potentiometer a sinistra ad ius diu.)