Aka chiqanxa: Uta » Blog ukax uñt’ayatawa » parámetros de corte de una máquina de corte láser-4000S

parámetros de corte ukaxa mä maquina de corte láser-4000S

Uñakipatanaka: 0 Qillqiri: Sitio Editor Uñt’ayaña pacha: 2025-10-22 Uñstayata: Sityu

	RFL-4000S(50u) ukax mä juk’a pachanakanwa.		Cutting Head ukax Ratio Óptico satawa		150Colimación 100 / Distancia focal 150. Ukaxa mä juk’a pachanakwa lurasi
	RFL-4000S(50u) ukax mä juk’a pachanakanwa.		Cutting Head ukax Ratio Óptico satawa
Matiryala	Thixni [mm] ukhama.	Ukax [m/min] ukhamawa.	Ch’ama [W].	Gas ukat juk’ampinaka	Presión de aire [bar] ukax mä juk’a pachanakanwa.	Boquilla [mm] ukaxa.	Posición Focal ukaxa [mm].	Cutting Altura [mm] ukat juk’ampinaka.
Acero al Carbono ukat juk’ampinaka	1	36-50 ukat juk’ampinaka	4000	N2/Air ukat juk’ampinaka	12	1.5S.Ukaxa 1.5S	0.5
	2	18-22 uka qillqatanaka	4000		12	1.5S.Ukaxa 1.5S	-1.5
	3	8-12 uka qillqatanaka	4000		12	2.0S	-2
Acero al Carbono ukat juk’ampinaka	3	4-4.5 uka qillqatanaka	2400	O2	0.5	1.0D	+3.5
	4	3-3.5 uka qillqatanaka	2400		0.5	1.0D	+4.5
	5	2.9-3.2 uka tuqinakata	2400		0.5	1.0D	+4.5
	6	2.7-2.8 uka qillqatanaka	3000		0.6	1.0D	+5
	8	2.4-2.5 uka qillqatanaka	3000		0.6	1.2D	+5.5 ukat juk’ampinaka
	10	1.9-2.1 uka tuqita	4000		0.65	1.2D	+6
	12	1.2-1.5 uka qillqatanaka	4000		0.65	3.0D	+4
	14	0,9-1 ukhakama	2200-2600 ukakama		0.6	4.0D	+4
	16	0,7-0,9 ukhakama	2200-2600 ukakama		0.6	4.0D	+4.5
	18	0,6-0,7 ukhakama	2200-2600 ukakama		0.6	4.5D	+5
	20	0,55-0,65 ukhakama	2200-2800 ukakama		0.6	5.0D	+5
	22	0,5-0,6 ukhakama	2200-2800 ukakama		0.6	5.0D	+5
	25	0,4-0,5 ukhakama	2400-3000 ukhakama		0.6	5.0D	+5
Acero Inoxidable ukat juk’ampinaka	1	42-55 ukat juk’ampinaka	4000	N2	12	1.5S.Ukaxa 1.5S	0.5
	2	21-28 uka qillqatanaka			12	2.0S	-1.5
	3	9-12 uka qillqatanaka			12	2.0S	-2
	4	6.5-8 uka qillqatanaka			14	3.0S	-3
	5	5-5.5 uka qillqatanaka			16	3.0S	-3.5
	6	3.3-4 uñakipt’aña			14	3.5S.Ukaxa mä juk’a pachanakwa lurasi	-4.5
	8	1.5-2			18	3.5S.Ukaxa mä juk’a pachanakwa lurasi	-5
	10	1.2-1.5 uka qillqatanaka			18	5.0S	-8
	12	0.8			18	5.0S	-8.5
Aluminio ukat juk’ampinaka	1	35-40 uka qillqatanaka	4000	N2	12	1.5S.Ukaxa 1.5S	0
	2	18-22 uka qillqatanaka			12	2.0S	0
	3	8-10 uka qillqatanaka			14	2.0S	-1
	4	6-7			14	2.5S.Ukaxa mä juk’a pachanakwa lurasi	-2
	5	4-5 ukat juk’ampinaka			16	3.0S	-3
	6	2.5-3			16	3.0S	-3.5
	8	1-1.2 uka tuqita			16	3.5S.Ukaxa mä juk’a pachanakwa lurasi	-4
	10	0.8			16	5.0S	-5
Latón satänwa	1	30-35 uka qillqatanaka	4000	N2	12	1.5S.Ukaxa 1.5S	0
	2	15-18 uka qillqatanaka			12	2.0S	0
	3	7.5-9 uka qillqatanaka			14	2.5S.Ukaxa mä juk’a pachanakwa lurasi	-1
	4	5-6			14	3.0S	-2
	5	3-4 ukat juk’ampinaka			16	3.0S	-2.5
	6	2-2.5 uka qillqatanaka			16	3.0S	-3
	8	0,8-1 ukhakama			16	3.5S.Ukaxa mä juk’a pachanakwa lurasi	-3.5

Qhansuyi: Tabla ukanxa wila chimpunakaxa parámetros prototipo ukanakawa. Aka parámetros ukaxa chiqapa lurawi pachana kunaymana tuqinakata wali ch’amanchatawa, ukhamarusa jisk’a lote lurañatakikiwa wali askiwa ukatxa janiwa jach’a lote lurañataki ukhamaraki lurañatakixa wakiskiti. Mä láser ukax juk’amp ch’amampiw apnaqañax wali askiwa.

Uka tuqit yatxatatanaka

contenido ukax ch’usawa!

Uñt’at Blogs ukanaka

parámetros de corte ukaxa mä maquina de corte láser-4000S

KUNAS JIWASAN UTJAÑAPATAKI

KUNSA LURASPA

JIWASAN TECNOLOGÍA UKATXA

SIRWISYU